Search results for "Surface roughness"

The influence of Cr and Ni doping on the microstructure of oxygen containing diamond-like carbon films

2021

Abstract Non-hydrogenated diamond-like carbon (DLC) films doped with metals and oxygen were deposited by direct current magnetron sputtering. The influence of chromium and nickel on the surface morphology, elemental composition, bonding structure, adhesion force, optical transmittance and nanohardness of the films was characterized by atomic force microscopy (AFM), energy dispersive X-ray spectroscopy (EDX), multi-wavelength Raman spectroscopy, UV–VIS–NIR spectrophotometry and nanoindenter. The surface roughness was reduced with the addition of Cr (7.4 at. %) or Ni (8.9 at. %) into DLC films. The EDX measurements indicated that the addition of Cr increased the oxygen content by ~37%, while …

Influence of surface topography on depth profiles obtained by Rutherford backscattering spectrometry

2000

A method for determining correct depth profiles from samples with rough surfaces is presented. The method combines Rutherford backscattering spectrometry with atomic force microscopy. The topographical information obtained by atomic force microscopy is used to calculate the effect of the surface roughness on the backscattering spectrum. As an example, annealed Au/ZnSe heterostructures are studied. Gold grains were observed on the surfaces of the annealed samples. The annealing also caused diffusion of gold into the ZnSe. Backscattering spectra of the samples were measured with a 2 MeV 4He+ ion beam. A scanning nuclear microprobe was used to verify the results by measuring backscattering fro…

Refractive index controlled by film morphology and free carrier density in undoped ZnO through sol-pH variation

2018

Abstract Zinc oxide thin films, prepared by the sol-gel process, were deposited on glass substrate using spin coating technique. The sol-pH effect on the optical parameters was studied for alkaline sol. The surface roughness was investigated by atomic force microscopy (AFM) and varied from 20 to 40 nm. The optical transmission measurements were carried out to evaluate the behavior of the extinction coefficient and the refractive index. An exponential decay of the refractive index ‘n’ as a function of wavelength was observed. The refractive index increases slightly when the pH increases to pH = 9.5 where it reaches its maximum. Beyond this value, it decreases sharply. This behavior has been …

The WISE 2000 and 2001 Field Experiments in Support of the SMOS Mission:Sea Surface L-Band Brightness Temperature Observations and Their Application …

2004

Camps, Adriano ... et al.-- 20 pages, 16 figures, 3 tables

Evaluating roughness effects on C-band AMSR-E observations

2014

International audience; The usefulness of microwave remote sensing to retrieve near-surface soil moisture has already been demonstrated in many studies. However, obtaining high quality estimates of soil moisture is influenced by many effects from soil, vegetation and atmosphere; one of the key parameters is surface roughness. This research focusses on a semi-empirical method to evaluate the roughness effects from space borne observations. Global maps of roughness effects are evaluated at C-band from AMSR-E measurements.

2018

The Radar Vegetation Index (RVI) is a well-established microwave metric of vegetation cover. The index utilizes measured linear scattering intensities from co- and cross-polarization and is normalized to ideally range from 0 to 1, increasing with vegetation cover. At long wavelengths (L-band) microwave scattering does not only contain information coming from vegetation scattering, but also from soil scattering (moisture & roughness) and therefore the standard formulation of RVI needs to be revised. Using global level SMAP L-band radar data, we illustrate that RVI runs up to 1.2, due to the pre-factor in the standard formulation not being adjusted to the scattering mechanisms at these lo…

Global-Scale Evaluation of Roughness Effects on C-Band AMSR-E Observations

2015

Quantifying roughness effects on ground surface emissivity is an important step in obtaining high-quality soil moisture products from large-scale passive microwave sensors. In this study, we used a semi-empirical method to evaluate roughness effects (parameterized here by the parameter) on a global scale from AMSR-E (Advanced Microwave Scanning Radiometer for EOS) observations. AMSR-E brightness temperatures at 6.9 GHz obtained from January 2009 to September 2011, together with estimations of soil moisture from the SMOS (Soil Moisture and Ocean Salinity) L3 products and of soil temperature from ECMWF’s (European Centre for Medium-range Weather Forecasting) were used as inputs in a retrieval…

The application of the random balance method in laser machining of metals

2008

International audience; Features peculiar to laser technology offer some advantages over more traditional processes, but, like all processes, it has its limitations. This article studies the limitations of laser machining of metals, and quantifies, through an experimental design method, the influence of operating parameters on productivity and on the quality of the machined surface. Three study materials were used: an aluminium alloy, stainless steel and a titanium alloy. An initial reading of the results indicates that productivity depends mainly on the frequency of the laser pulse and that the aluminium alloy behaves differently from the other two. The quality of the machined surface, jud…

Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H 3 PO 4 /H 2 SO 4

2017

Abstract In recent decades, new manufacturing processes have been developed such as Thermal Spray Coating (TSC) and Additive Layer Manufacturing (ALM), which reduce or avoid machining of parts with complex geometries. This study aims to develop an Electropolishing (EP) process for TSC and ALM 316L Stainless Steel (SS). EP is an anodic dissolution process currently used in industry to reduce surface roughness and obtain a bright and smooth finish. The EP mechanism was studied, in a mixture of H3PO4 and H2SO4, for TSC, ALM and “cast” SS in order to determine the best conditions (time, temperature, potential). Special attention was paid to surface characterization by combining several techniqu…

Influence of residual stress, surface roughness and crystallographic texture induced by machining on the corrosion behaviour of copper in salt-fog at…

2012

International audience; The influence of quadratic stress, crystallographic texture, lubrication and surface roughness generated by superfinish turning on the corrosion behaviour of pure copper was quantified in salt-fog atmosphere. This was done using statistical analysis (Pearson's correlation matrix). Three compounds were found after corrosion tests: atacamite/paratacamite and a black layer (mixture of the lubricant and the salt atmosphere). Surface characteristics were classified according to their decreasing influence on the formation of atacamite/paratacamite as follows: surface roughness and quadratic stress. Lubrication and the crystallographic texture have the lowest influence on c…